VESD05A6A-HAF document number 81880 rev. 1.2, 11-jun-10 vishay semiconductors www.vishay.com 1 19371 3 6 54 7 1 2 20517 1 for technical support, please contact: esdprotection@vishay.com 6-line esd-protection diode array in llp75 features ? ultra compact llp75-7l package ? 6-line esd-protection ? low leakage current i r < 0.1 a ? low load capacitance c d = 13 pf ? esd-immunity acc. iec 61000-4-2 15 kv contact discharge 15 kv air discharge ? working voltage range v rwm = 5 v ? e4 - precious metal (e .g. ag, au, nipd, nipdau) (no sn) ? compliant to rohs directive 2002/95/ec and in accordance to weee 2002/96/ec marking (example only) dot = pin 1 marking xx = date code yy = type code (see table below) ordering information package data ** please see document ?vishay material category policy? www.vishay.com/doc?99902 21001 xx yy device name ordering code taped units per reel (8 mm tape on 7" reel) minimum order quantity VESD05A6A-HAF VESD05A6A-HAF-gs08 3000 15000 device name package name type code weight molding compound flammability rating moisture sensitivity level soldering conditions VESD05A6A-HAF llp75-7l at 4.2 mg ul 94 v-0 msl level 1 (according j-std-020) 260 c/10 s at terminals
www.vishay.com 2 document number 81880 rev. 1.2, 11-jun-10 VESD05A6A-HAF vishay semiconductors for technical support, please contact: esdprotection@vishay.com absolute maximum ratings application note: a) with the VESD05A6A-HAF 6 different signal or data lines can be clamped to ground. due to the different clamping levels in forward and reverse direction the VESD05A6A-HAF clamping behavior is bi directional and as ymmetrical (bias). b) if symmetrical clamping behaviour is required the VESD05A6A-HAF can also be used as a bi directional sy mmetrical protection device protecting up to 5 lines. in this case pin no. 7 must not be connected. rating test condition symbol value unit peak pulse current bias-mode: each input (pin 1 - pin 6) to ground (pin 2); acc. iec 61000-4-5; t p = 8/20 s; single shot i ppm 2.5 a bisy-mode: each input (pin 1 - pin 6) to any other input pin. pin 2 not connected. acc. iec 61000-4-5; t p = 8/20 s; single shot i ppm 2.5 a peak pulse power bias-mode: each input (pin 1 - pin 6) to ground (pin 2); acc. iec 61000-4-5; t p = 8/20 s; single shot p pp 33 w bisy-mode: each input (pin 1 - pin 6) to any other input pin. pin 2 not connected. acc. iec 61000-4-5; t p = 8/20 s; single shot p pp 43 w esd immunity acc. iec61000-4-2; 10 pulses bias-mode: each input (pin 1 - pin 6) to ground (pin 2) contact discharge v esd 15 kv air discharge v esd 15 kv acc. iec 61000-4-2 ; 10 pulses bisy-mode: each input (pin 1 - pin 6) to any other input pin. pin 2 not connected contact discharge v esd 10 kv air discharge v esd 10 kv operating temperature junction temperature t j - 40 to + 125 c storage temperature t stg - 55 to + 150 c l1 l2 l3 l4 l5 l6 19365 3 6 54 7 1 2 l1 l2 l3 l4 l5 19366 3 6 54 7 1 2
VESD05A6A-HAF document number 81880 rev. 1.2, 11-jun-10 vishay semiconductors www.vishay.com 3 for technical support, please contact: esdprotection@vishay.com electrical characteristics ratings at 25 c, ambient temperature unless otherwise specified VESD05A6A-HAF bias mode (between pin 1, 2, 3, 4, 5 or 6 and pin 7) typical characteristics t amb = 25 ? c, unless otherwise specified parameter test conditions/remarks symbol min. ty p. max. unit protection paths number of li nes which can be protected n lines 6 lines reverse stand off voltage at i r = 0.1 a v rwm 5v max. reverse current at v r = 5 v i r < 0.01 0.1 a reverse break down voltage at i r = 1 ma v br 66.77.5v reverse clamping voltage at i pp = 1 a v c 910v at i pp = i ppm = 2.5 a v c 12 13 v forward clamping voltage at i pp = 1 a v f 22.5v at i pp = i ppm = 2.5 a v f 3.2 4 v line capacitance at v r = 0 v; f = 1 mhz c d 13 15 pf at v r = 2.5 v; f = 1 mhz c d 8pf figure 1. esd discharge current wave form acc. iec 61000-4-2 (330 ? /150 pf) 0 % 20 % 40 % 60 % 8 0 % 100 % 120 % - 10 0 10 20 30 40 50 60 70 8 0 90 100 time (ns) discharge c u rrent i esd rise time = 0.7 ns to 1 ns 53 % 27 % 20557 figure 2. 8/20 s peak pulse current wave form acc. iec 61000-4-5 0 % 20 % 40 % 60 % 8 0 % 100 % 010203040 time ( s) i ppm 20 s to 50 % 8 s to 100 % 2054 8
www.vishay.com 4 document number 81880 rev. 1.2, 11-jun-10 VESD05A6A-HAF vishay semiconductors for technical support, please contact: esdprotection@vishay.com figure 3. typical capacitance c d vs. reverse voltage v r figure 4. typical forward current i f vs. forward voltage v f figure 5. typical reverse voltage v r vs. reverse current i r 1994 8 v r ( v ) 04 3 2 1 14 16 12 c d (pf) 5 f = 1 mhz 2 10 8 6 4 0 19949 v f ( v ) 0.5 1 0. 8 0.7 0.6 0.01 100 10 1 0.1 0.001 i f (ma) 0.9 1.1 19950 i r ( a) 0.01 100 10 1 0.1 1 5 4 3 2 0 v r ( v ) 10 000 1000 7 6 8 figure 6. typical clamping volt age vs. peak pulse current i pp figure 7. typical clamping perf ormance at + 8 kv contact discharge (acc. iec 61000-4-2) figure 8. typical clamping performance at - 8 kv contact discharge (acc. iec 61000-4-2) 19951 i pp (a) 04 3 2 1 - 4 4 2 0 - 2 - 6 v c ( v ) 8 6 10 14 12 meas u red acc. iec 61000-4-5 ( 8 /20 s - w a v e form) for w ard re v erse 0.5 3.5 2.5 1.5 v c acc. iec 61000-4-2 + 8 k v contact discharge 19994 t (ns) 20 10 0 - 10 - 20 60 40 20 0 v c-esd ( v ) 30 8 0 100 40 8 0 70 60 50 90 acc. iec 61000-4-2 - 8 k v contact discharge 19995 t (ns) 20 10 0 - 10 - 8 0 0 - 20 - 40 - 60 - 100 v c-esd ( v ) 30 20 40 8 0 70 60 50 90 40
VESD05A6A-HAF document number 81880 rev. 1.2, 11-jun-10 vishay semiconductors www.vishay.com 5 for technical support, please contact: esdprotection@vishay.com package dimensions in millimeter s (inches): llp75-7l figure 9. typical max. clamping voltage at esd contact discharge (acc. iec 61000-4-2) v c-esd 19954 10 5 0 0 150 100 50 - 50 v c-esd ( v ) 15 200 20 v esd (k v ) - 150 - 200 - 100 acc. iec 61000-4-2 contact discharge 1.05 (0.041) 0.5 (0.020) 0.95 (0.037) heat sink 0.3 (0.012) 0.2 (0.00 8 ) 0.3 (0.012) 0.2 (0.00 8 ) 0.3 (0.012) 0.2 (0.00 8 ) 0.55 (0.022) 0.45 (0.01 8 ) 0.6 (0.024) 0.25 (0.010) 0.6 (0.024) 0.54 (0.021) 0.05 (0.002) 0 (0.000) 0.15 (0.006) 1.65 (0.065) 1.55 (0.061) 1.65 (0.065) 1.55 (0.061) pin 1 marking 0.5 (0.020) 0.5 (0.020) 0.3 (0.012) 0.3 (0.012) 0.15 (0.006) 0.15 (0.006) 0.5 (0.020) 0.5 (0.020) 1 (0.039) 0.25 (0.010) solder resist mask solder pad doc u ment no.:s 8 - v -3906.02-014 (4) 20500 created - date: 04. april 2006 foot print recommendation: 1 (0.039) 1 (0.039)
document number: 91 000 www.vishay.com revision: 11-mar-11 1 disclaimer legal disclaimer notice vishay all product, product specifications and data ar e subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectivel y, vishay), disclaim any and all liability fo r any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicab le law, vishay disc laims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, incl uding without limitation specia l, consequential or incidental dama ges, and (iii) any and all impl ied warranties, including warran ties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of pro ducts for certain types of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in gene ric applications. such statements are not binding statements about the suitability of products for a partic ular application. it is the customers responsibility to validate that a particu lar product with the properties described in th e product specification is su itable for use in a particul ar application. parameters provided in datasheets an d/or specifications may vary in different applications and perfo rmance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vishays term s and conditions of purchase, including but not limited to the warranty expressed therein. except as expressly indicated in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vishay product co uld result in person al injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk and agr ee to fully indemnify and hold vishay and it s distributors harmless from and against an y and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that vis hay or its distributor was negligent regarding the design or manufact ure of the part. please contact authorized vishay personnel t o obtain written terms and conditions regarding products designed fo r such applications. no license, express or implied, by estoppel or otherwise, to any intelle ctual property rights is gran ted by this document or by any conduct of vishay. product names and markings noted herein may be trademarks of their respective owners.
|
